Linux version 2.6.16.57-arm5 (root@LS-GL7D6) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #2 Sun Dec 30 11:37:40 BRT 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3 

Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
  DMA zone: 32768 pages, LIFO batch:7
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110520KB available (3197K code, 441K data, 100K init)
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL 

 Detected Tclk 166664740 and SysClk 200000000 
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 
Done. 
cesadev_init(c00111f0)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
JFFS version 1.0, (C) 1999, 2000  Axis Communications AB
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
JFS: nTxBlock = 984, nTxLock = 7877
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0' 
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
  Vendor: SAMSUNG   Model: HD501LJ           Rev: CR10
  Type:   Direct-Access                      ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1672b60
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
CFI: Found no phys_mapped_flash device at location zero
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
phys_mapped_flash: Found an alias at 0x40000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x80000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0xc0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x100000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x140000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x180000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x1c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x200000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x240000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x280000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x2c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x300000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x340000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x380000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x3c0000 for the chip at 0x0
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using ehci_platform and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 100K
SAL (ERROR)  0 0 0 :Scsi command completed. pScb c16d49c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BAD_SCSI_COMMAND
SAL (ERROR) CDB:12 1 0 0 fe 0 
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 c 0 0 0 0 24 0 0 0 0 0 0 0 
SAL (ERROR)  0 0 0 :Scsi command completed. pScb c16d49c0, ScsiStatus 2 completionStatus MV_SCSI_COMPLETION_BAD_SCSI_COMMAND
SAL (ERROR) CDB:12 1 0 0 fe 0 
SAL (ERROR) Sense Data:70 0 5 0 0 0 0 c 0 0 0 0 24 0 0 0 0 0 0 0 
Adding 297160k swap on /dev/sda5.  Priority:-1 extents:1 across:297160k
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
NET: Registered protocol family 5
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
